The new 6012/6013/6015/6016 Bluetooth multimeter is advanced instrument meeting the needs of today’s technology with a Bluetooth communication and Android based application for mobile phones, so now all the data is made available on your mobile screen. It is made for professional use that offers safety, high resolution, large range count, reliability, ruggedness, a complete tool for test automation and is equipped with more than 30 different measuring functions
Tool for automation, Bluetooth 2.0 Interface and Application for android phone
location With ready to use communication protocol, one can easily automate his test system. The extensive data capturing and analysis is possible with RISHABH 601X Android
Instead of cable, the higher communication distance can be achieved (10m) which also allows a safe distance for analysis in hazardous areas, meter can be connected and readings can be viewed. Graphical and Tabular analysis is possible over android application as well as Data logging facility and setting of parameters via mobile can be done. So whole data is made available on screen of mobiles. The application supports Ice cream Sandwich, Jelly bean, Kitkat & lollypop versions of android.
Low pass filter(LPF) in VAC10MΩ& VAC1MΩ (6013, 6015, 6016)
In LPF mode DMM rejects all high frequency noise making it suitable for taking measurements on inverters and high frequency drives.
Low input impedance (Ri = 1MΩ) (6013, 6015, 6016)
Trouble shooting a branch circuit with dead or disconnected circuit is made easy with VAC1MΩ. Low impedance VAC1MΩ measurement helps eliminating erroroneous readings resulting from ghost voltages caused by long wires that share a common conduit.
Current measurement with clamp sensor
Measurement with various clamp sensors is possible, which helps in accurate measurement of current from 60mA to 6000A (600A for 6012) without interrupting the circuit. The measured current is automatically calculated from the selected clamp ratio.
Instrument contains a single fuse of 16A common for all the ranges of current from 600μA to 10A AC/DC as
compared to the two fuses in traditional DMMs. This eliminates the accidental blowing of 1.6A fuse due to
operator's error when higher current is applied in lower Ranges.
Square Wave Output (6015, 6016)
A square wave output can be generated from the DMM with the user selectable frequency and adjustable duty
cycle. This can be used as baud rate generator, to check flow meters, to test frequency counters, accelerometer and frequency transmitter. It can also be used as audio signal in audio signal testing.
True RMS measurement with high crest factors
Accurate true RMS measurement of distorted waveform with crest factor CF between 1 to 10.
Adjustable Beep Level
With Beep level setting, the limit for continuity can be adjusted from 10Ω to 90Ω depending upon application.
Room temperature measurement
Room temperature can be sensed and measured without any external sensor. The same is used as internal
reference temperature in thermocouple based temperature Measurements
RISHABH 6012 / 6013 / 6015 / 6016
60mv & 600mV DC & ACDC
This helps in accurate measurement of low output voltages <600mV from sensors & transmitters. High frequency low voltage signal from RF transmitters can also be measured. Signal as low as 0.001mV can be measured accurately.
External Power Adapter (DC Jack)
The external power supply adapter helps in conserving battery while performing long hours of measurements.
When DC jack is connected batteries inside DMM are electronically disconnected, and reconnected in absence of mains, hence there is no need of removing the battery when using the power adapter.
100kHz Bandwidth (6016)
Alternating voltages with frequencies up to 100kHz can be measured accurately. This is useful while analyzing high frequency analog signals.
Fully programmable GO NO-GO
The Go – No - Go function gives an indication through a buzzer for the applied input lying inside or outside the set band. The values for low limit, high limit and buzzer condition can be easily set through NoGo function in menu settings. Once the NoGo function is set, user can get busy doing other activities in the vicinity of the meter, whenever the condition is met it will be indicated by a buzzer. It eliminates the need of operator to continuously monitor the display.
True RMS measurement with high crest factors Accurate true RMS measurement of distorted waveform with crest factor CF between 1 to 10.
DMM 6015/6016 offers continuous data logging of up to 32000 readings with real time stamping. Log rate is adjustable from as low as 0.1 sec to as high as 1hr.
Auto Power OFF with adjustable timing
Flexibility to adjust “Auto off ” period from 5 minutes to 60 Minutes.
Min / Max / Avg measurement
Min/Max/Avg function records the minimum, maximum and average of all the readings applied since its activation. With dual display it makes it even flexible for the user to keep the trace of the applied readings while viewing Min/Max/Avg readings. The average reading is useful for smoothing out unstable inputs, & verifying circuit Performance.
Self-battery voltage measurement
Capable of measuring self-battery voltage.
Data logged on meter can be viewed directly on the meter itself, hence the data analysis is also possible without a PC based software. However, for graphical and large data analysis PC based software can be used.
Dangerous Contact Voltage Indication
Presence of hazardous voltage (>35Vrms 50/60Hz and 50Vdc) at the contact terminal are indicated on display.
This is very useful while performing measurements in the circuit which takes longer time to discharge its capacitors, or where unexpected danger voltage are present.
Dedicated keys for easy navigation
Dedicated navigation keys makes scrolling through menu and setting of parameters easy & comfortable.
Separate fuse compartment
Easier access to fuse when replacing the blown fuse.